How to Build Your Own $3.2bln Nest Startup Using Java SE Embedded Tech (Part 7)

So, you've got your Parallax Single Relay Board. Next you need to connect this to your furnace, fan, and A/C control wires... and, not burn down your house in the process. Got that? Good.

Refer back to your thermostat wires. We need to connect a Relay Board to each of the control wires for the Fan, Heat call, and Cool call. Here's a reminder which wire is which.

    Red - R - 24VAC
         or
    Red - Rh - 24VAC (dedicated to heat call)
    Red - Rc - 24VAC (dedicated to cooling call)

    Green - G - Fan on
    White - W - Heat call
    Yellow - Y - Cool call
    Blue or Black - C - Common

You will need 3 Relay Boards connecting to the Raspberry Pi to control the 3 house thermostat control wires (Green for Fan, White for Heat, and Yellow for Cool). First, make sure on your Adafruit PiTFT has the 2x13 male header properly soldered on to it to daisy chain your RPi header pins (to allow your Relay Boards to connect down to the RPi). This way your Adafruit PiTFT can use the SPI pins (SCK, MOSI, MISO, CE0, CE1) plus GPIO #24 and #25 for its use, while we use GPIO #00, #01, and #04 for the Relay Boards. It's nice to share.

On each Relay Board, connect the + to the +5 VDC pin on your Adafruit PiTFT (male header pin #2). Make use of continuous jumper wires to share the one +5 VDC pin with all 3 of the Relay Boards. Then, connect the - to the GND pin (male header pin #6) using a continuous jumper wire to share this pin also. And, finally connect the S pin of one of your Relay Boards to GPIO #00 (pin #3), one S pin to GPIO #01 (pin #5), and the final S pin to GPIO #04 (pin #7).

Then connect all 3 Relay Boards Common screw down connector to the C - Common wire of your thermostat. Connect one Relay Board Normal Open (NO) screw down connector to the Green Fan wire, one NO screw down connector to the White Heat wire, and the final NO screw down connector to the Yellow Cool wire. Cool? Cool!

You are good to go for the next step!

See, not so bad still, right? ;-)

Full series of steps:
How to Build Your Own $3.2bln Nest Startup Using Java SE Embedded Tech (Part 1)
How to Build Your Own $3.2bln Nest Startup Using Java SE Embedded Tech (Part 2)
How to Build Your Own $3.2bln Nest Startup Using Java SE Embedded Tech (Part 3)
How to Build Your Own $3.2bln Nest Startup Using Java SE Embedded Tech (Part 4)
How to Build Your Own $3.2bln Nest Startup Using Java SE Embedded Tech (Part 5)
How to Build Your Own $3.2bln Nest Startup Using Java SE Embedded Tech (Part 6)
How to Build Your Own $3.2bln Nest Startup Using Java SE Embedded Tech (Part 7)
How to Build Your Own $3.2bln Nest Startup Using Java SE Embedded Tech (Part 8)
How to Build Your Own $3.2bln Nest Startup Using Java SE Embedded Tech (Part 9)
<<< Previous  | Next >>>

Comments:

Post a Comment:
Comments are closed for this entry.
About

Hinkmond Wong's blog on making the Internet of Things (IoT) smarter with Java Technologies

Search

Archives
« March 2015
SunMonTueWedThuFriSat
1
2
3
4
5
6
7
8
10
11
12
14
15
16
17
18
19
20
21
22
25
26
27
28
29
30
31
    
       
Today